steingar
Taxi to Parking
The last time I did several landings in a closed pattern (for nighttime currency) I left the pump on the whole time, mostly to save wear and tear on the switch. That, and the dman thing wasn't easy to see in the dark.
Piper fuel pump usage/overusage?
- Thread starter alfadog
- Start date
RotorAndWing
Final Approach
- Joined
- Sep 5, 2008
- Messages
- 8,496
- Location
- Other side of the world
- Display Name
Display name:
Rotor&Wing
Hmmmm. I'd like to see a reference for that one.
I think you are confusing the electric engine fuel pump for the electric tip tank fuel transfer pump, which does come on with the master switch.
The tip tank transfer pump is wired through the landing light CB.
Last edited:
Hmmm... Where does the tip tank transfer pump transfer to?
Clark1961
Touchdown! Greaser!
- Joined
- Jun 7, 2008
- Messages
- 17,737
- Display Name
Display name:
Display name:
The primer uses the boost pump on the TSIO-360-F
RotorAndWing
Final Approach
- Joined
- Sep 5, 2008
- Messages
- 8,496
- Location
- Other side of the world
- Display Name
Display name:
Rotor&Wing
You own a 310 and flew a 421, and you don't know the answer to that?
In the twin Cessna’s with tip tanks, they found that if you were low on fuel and in a fairly steep nose down attitude the fuel pump could not pick up that last ~ 5 gallons of fuel from the front of the tank. The solution was to put a transfer tube at the front of the tip tank - and have a constant running electric fuel pump draw fuel from that area and put it next to the fuel pump. The operation of these pumps should be checked during preflight – just turn the battery master switch on and go out and listen to these “ticker” pumps (located at the rear of each tank) operate. If no noise – no go. They are required to be operating to fly
Interesting, nope, did not know that. It was explained to me incorrectly and I've never taken the system apart before to find out differently.
RotorAndWing
Final Approach
- Joined
- Sep 5, 2008
- Messages
- 8,496
- Location
- Other side of the world
- Display Name
Display name:
Rotor&Wing
Interesting. That's a very basic part of the preflight on any twin Cessna. It's even discussed in the POH.
I knew the pump should be running, did not know it was an extra pump tossed in. BTW, It's not mentioned in my POH as it didn't exist when my POH was written.
RotorAndWing
Final Approach
- Joined
- Sep 5, 2008
- Messages
- 8,496
- Location
- Other side of the world
- Display Name
Display name:
Rotor&Wing
OK.
But you have stated previous to owning the 310 you flew 421 for someone, and it is in the POH of the 421 (as it is with all later 300 and 400 series).
20 years is a long time past a checkout, but I don't remember that being brought up. However, I will admit not having read the POH word for word.
- Joined
- May 11, 2010
- Messages
- 20,775
- Location
- Charlotte, NC
- Display Name
Display name:
Snorting his way across the USA
Probably, as it has the Lycoming engine. The 201T, no.
I had a separate primer button on mine but that may well be so.
dell30rb
Final Approach
I use mine in a similar manner. Does not hurt to run it a few minutes longer. Generally I turn it on/off with the landing light.
Handbook on the lycoming warrior does call for the pump on when switching tanks
Clark1961
Touchdown! Greaser!
- Joined
- Jun 7, 2008
- Messages
- 17,737
- Display Name
Display name:
Display name:
The prime button just runs the fuel pump in low (IIRC).
This is what I do, same thing for switching tanks.
Primer button on a Continental set up should activate on 'High' IIRC. I use high pump full throttle mixture rich till the needle hits up for between a 4 and 7 count depending on the conditions, bring the mixture back to '6' (where I find it leans well for idle) and the throttle back to about 1.5" off the idle stops. Hot start or cold, they start in 2-3 blades on IO-470Ds.
Clark1961
Touchdown! Greaser!
- Joined
- Jun 7, 2008
- Messages
- 17,737
- Display Name
Display name:
Display name:
You are correct, high it is. On the TSIO-360-F the primer button activates high side of the pump and opens the valve to the a separate primer system (two primer nozzles).
(reading the POH is a good thing, should have done it before I posted).
- Joined
- May 11, 2010
- Messages
- 20,775
- Location
- Charlotte, NC
- Display Name
Display name:
Snorting his way across the USA
Note to self... Read the POH before posting.
It's simple really, there are only 2 options on how it works with FI, 'Low' on a Continental is the same as 'On' with a Lycoming/Bendix which also BTW is as with a carb; it acts as a lift pump to provide the engine with fuel in normal operations. High on a Continental is a high rate delivery for priming and running the engine in a injection pump failure scenario. If you turn a Continental on 'High' to swap tanks on a running engine, unless you are super hard LOP, you'll kill the engine flooding it.
Last edited:
CMTowner
Line Up and Wait
I keep the fuel pump on until I complete the after takeoff checklist, and turn it back on when I'm setting up for my downwind to base turn.
If I'm doing pattern work, I just leave it on full time, much like the landing light. Too much chance to forget turning it back on if I turn it off all the time.
If I'm doing pattern work, I just leave it on full time, much like the landing light. Too much chance to forget turning it back on if I turn it off all the time.
jasont
Pre-Flight
Leave it on during takeoff and landing. Dont worry about it wearing out. Its not a gravity feed system and if you lose a pump during a critical stage, you wont even know till you cut the pump off on the ground. 
- Joined
- Jul 4, 2006
- Messages
- 5,128
- Location
- Lincoln, Nebraska
- Display Name
Display name:
Jason W (FlyNE)
One thing that I try to do on every flight is actually verify that both pumps work. I turn on the electric pump before I start the engine and watch the fuel pressure come up. Then I start the engine. Once the engine is running I shut off the electric pump. If the engine continues to run I know that the mechanical pump is working. Then I just turn it back on right before I take the runway.
I've seen quite a few pilots turn the electric pump on to start the engine and leave it on until they're at 1500 ft. I'd rather not have the 1500 ft mark be the first time that I've verified that the mechanical pump is functional.
I've seen quite a few pilots turn the electric pump on to start the engine and leave it on until they're at 1500 ft. I'd rather not have the 1500 ft mark be the first time that I've verified that the mechanical pump is functional.
jasont
Pre-Flight
That's the checklist procedure. The runup should be done with the aux pump off; then back on before takeoff.
dell30rb
Final Approach
I have posted on here before, realized i was not 100% sure, then scrambled to confirm in the POH before someone calls BS on me haha
alfadog
Final Approach
My cold start in the Arrow is to turn on the pump, prime, turn it off, start, and off until pre-takeoff checks.
- Joined
- May 11, 2010
- Messages
- 20,775
- Location
- Charlotte, NC
- Display Name
Display name:
Snorting his way across the USA
To be honest, sometimes I forget to turn the pump back on to start the engine. Leaving it off only seems to be a problem on hot starts.
alfadog
Final Approach
What is your hot start process in the Arrow?
- Joined
- May 11, 2010
- Messages
- 20,775
- Location
- Charlotte, NC
- Display Name
Display name:
Snorting his way across the USA
Same as the cold start process, but don't prime. Throttle cracked, mixture idle cutoff, fuel pump on, crank until it starts to fire, then advance mixture forward.
Also hot starts are easier if on shutdown, you gradually decrease the mixture letting almost to the point of roughness for a bit, letting the fuel burn off before shutting the mixture off completely. I never turn the engine off by turning the mags off first, always the mixture, then the mags.
jesse
Touchdown! Greaser!
Does anyone?
alfadog
Final Approach
Same here except I don't run the pump except to prime for cold start.
Only for a moment. I lean near ICO, flip mags both off for a moment to hear it cut out, back on the ICO.
RotorAndWing
Final Approach
- Joined
- Sep 5, 2008
- Messages
- 8,496
- Location
- Other side of the world
- Display Name
Display name:
Rotor&Wing
We had Weldon electric fuel pumps on the Hughes 269 series helicopters. They were used to prime the engine, then after start brought back on. The POH stated it should be on for take off and landing and below 1'000 ft agl but we let them run continuous (as most operators do).
- Joined
- May 11, 2010
- Messages
- 20,775
- Location
- Charlotte, NC
- Display Name
Display name:
Snorting his way across the USA
Unfortunately, yes.
- Joined
- May 11, 2010
- Messages
- 20,775
- Location
- Charlotte, NC
- Display Name
Display name:
Snorting his way across the USA
I've done both. Seems to work better with the pump running, in my airplane.
pericynthion
Pre-takeoff checklist
My O-200 is hand-started, and hot starts can be a pain. If I'm just stopping for 5 minutes for gas and a pee then I'll leave the mixture at an appropriate setting and turn off the (electronic) ignition to kill it. This leaves a good fuel/air mix in the cylinders and it will then start on the first pull.
alfadog
Final Approach
I'll give it a try. Mine is starting pretty well but could be a little better.
alfadog
Final Approach
Same here with the Luscombe A-65. End of the day it is "mixture, mags, master" like anything else.
CMTowner
Line Up and Wait
Yes, I do this every few months to make sure the mags are grounding out. I don't want to leave my plane with a hot mag.
Every few months? I do it every flight.
- Joined
- May 11, 2010
- Messages
- 20,775
- Location
- Charlotte, NC
- Display Name
Display name:
Snorting his way across the USA
I occasionally do a mag check, but I don't totally shut the engine down, I just kill them momentarily, then shut the engine down with the mixture.
jesse
Touchdown! Greaser!
You can do that without completely shutting down.