Cessna hacks

GeorgeC

GeorgeC

Administrator
Management Council Member
Joined
Dec 5, 2010
Messages
5,503
Display Name
Display name:
GeorgeC
gearleg.png
C140A parts manual, fig 28-14, p/n 0441119, "hose-brake line protector" does not specify the size. It is 1/2" OD 1/4" ID x 1/2" long.

Also, after a couple of years, my fuel vent wore a hole in my cover. I duct taped a patch on the inside of the hole, then cut a 3/8" hole in a ping pong ball and put it over the vent before covering the airplane to eliminate the stress riser.
 
I usually see a 1/4" hose over those.
 
Tom-D said:
I usually see a 1/4" hose over those.
Click to expand...
That works. If the typical MIL-6000 or MIL-5593 hose has too big an OD, I'd use a bit of vacuum or windshield washer hose from the auto parts shop. It has a thinner wall.
 
GeorgeC said:
Also, after a couple of years, my fuel vent wore a hole in my cover. I duct taped a patch on the inside of the hole, then cut a 3/8" hole in a ping pong ball and put it over the vent before covering the airplane to eliminate the stress riser.
Click to expand...
The ping pong ball must have worked itself loose under the cover, as it was gone yesterday. Maybe a racquetball or tennis ball...
 
The 210 has some brake line clips glued to the strut with similar function, I cut a couple pieces of Aeroquip 306 hose and stuck them on the line... It's what I had laying around.
 
Turns out the same hose I used for the bumper makes a good field expedient pitot cover.
IMG_7009.jpg
 
Why would one need to manually cover the pitot when Cessna has provided an automatic metal one?
 
flyingbrit said:
Why would one need to manually cover the pitot when Cessna has provided an automatic metal one?
Click to expand...
Funny you should ask. Had it freeze on me a few months ago, then noticed it being wonky again last weekend. Finally had the shop blow it out...
IMG_7006.jpg
 
And I thought “Cessna Hacks” was going to be about hacking the wings off and reattaching them to the bottom like God intended....

:devil:

(Ducking and covering)
 
Half Fast said:
And I thought “Cessna Hacks” was going to be about hacking the wings off and reattaching them to the bottom like God intended....

:devil:

(Ducking and covering)
Click to expand...
More like us pilots on the left side of the bell curve...
 
flyingbrit said:
Why would one need to manually cover the pitot when Cessna has provided an automatic metal one?
Click to expand...
I don't ever remember seeing that part in any Cessna parts catalog. They were an aftermarket thing, and here in Canada the feds would get all excited when they saw one. Not approved, they'd say. Take it off or get fined.
 
Since Cessna Pitot Tubes were brought up…….

The Pitot Tube is rarely removed from its mount so it can be difficult to do so when the need arises. Bug?

In addition some screws are a rather odd variety like a 5-36 . It’s not a bad idea to assure screws can be removed at a convenient time . Annual?

Anti seize could help with FUTURE removals if applied earlier too.
 
Magman said:
In addition some screws are a rather odd variety like a 5-36 . It’s not a bad idea to assure screws can be removed at a convenient time . Annual?
Click to expand...
#4-40, IIRC. Not many shops keep that one in stock. It's really short, too.
 
Close.

Research shows Macfarlane and other sources seem to say it’s “ extra fine 6-40”.

Plan on not in stock,.
 
You must log in or register to reply here.
Back
Top