ktup-flyer
En-Route
Amendment. https://www.beechtalk.com/forums/viewtopic.php?f=43&t=171573That's a good looking TBone, albeit probably priced a bit high considering that it's sat for awhile and the radio stack.
Amendment. https://www.beechtalk.com/forums/viewtopic.php?f=43&t=171573That's a good looking TBone, albeit probably priced a bit high considering that it's sat for awhile and the radio stack.
How about a C-210? Anyone have experience with them? They have close to 2000 useful load and 6 seats. Is there room behind the backseats for baggage?
Preach!
Any chance you could answer my questions from post 115?
Get the 300. The consumption isn't so different that you're talking about a massive increase in hourly cost, and you will be a bit faster and you'll like the high DA performance.
I'm not worried about the hourly cost difference between 260/300. I realize there will be better DA performance with the 300. Just curious how much better it is. Is it dramatic or just a little better? Are 260 owners departing Denver saying "no big deal" or is it "Holy crap, the 260 has no business being in Denver!"
Thanks again for all the great information. I'm slowly soaking it up. I would truly love an Aztec or larger (402 & 414 were suggested) but after some rational airplane discussion (is that a thing? ) we're not comfortable with the care and feeding of a turbocharged twin with retracts. We wouldn't drag it out of the hangar for a $100 hamburger like we would a big single.
So, it's going to be....
A Cherokee Six. Looking at useful loads, the older 6s are better. UL on a PA-32-260 is as much as 200-300 pounds higher. But I have to give up 40 horses to carry the extra weight. Kinda like an aviation oxymoron.
Anyone flown both the 260 and 300? Is there a noticeable difference on takeoff and climb? Home Field is only 500' MSL. But in talking about fun trips, we thought of Santa Fe, NM at 6300'. Will I be dreaming of the extra 40 HP while rolling down the runway at KSAF?
Nothing wrong with Turbo models of the PA-32 body, either. If you operate at high DA locations, you'll appreciate the engine turning out the rated HP, vs. the fraction of it.
I love the cabin of the PA34 with that rear door. If only piper made the PA34 with 2 300hp normally aspirated engines and a useful load of 2,000 lbs
10-20% faster isn't really worth if you ask me. 10% faster on a 3-hour flight might save you what, 15-20 minutes? Meh.Well, the Aztec's wing (airfoil, specifically) is designed to haul a heavy load. It develops a lot of lift and a lot of drag. Most of the others were designed with more of an eye toward speed than load hauling.
I would recommend taking a look at the 310 as well. Useful loads are very good for the class, and it'll be 10-20% faster than an Aztec. I did some research on them earlier this year and did a brain dump of that here: All about Cessna 310s
10-20% faster isn't really worth if you ask me. 10% faster on a 3-hour flight might save you what, 15-20 minutes? Meh.
Depends on how you look at it I guess. Those are all long days. Depends on what the cost tradeoff is.So, really it's pretty much gonna be 20% unless you're comparing a really slow 310 and a really fast Aztec. And it's not about the 3-hour flight, it's about the day with three 3-hour legs in the slow plane, or three 2.5-hour legs (or better yet, two 3.75-hour legs!) with the faster plane.
Here is a video of a 210. I agree back seats aren’t the biggest. Great place for the smallest two on the plane. Fast, easy platform to fly and I don’t have to load over a wing. I have the IO-550 and flight plan for 165kts and 17 gal per hour ROP. The plane has 1503 lbs useful load. Almost 1100lbs payload with 500nm of fuel and a hour reserve. It will take about 3hrs to get there. Cherokee will take another 1/2hr. We were looking at the Saratoga/Lance and A-36 when we bought. Decided on the 210.
It's hard to see in the photo but this is what we hauled in the 310R this weekend to Reno. 4 peoples worth of stuff and we hauled some extra for friends taking the airlines. Included but not limited to...
2 hard sided Yeti 65 coolers
1 soft sided Yeti 18 cooler
1 approximately 1 gallon Yeti bottle
1 approximately 1/2 gallon Yeti bottle
2 Hydroflasks
4 duffle bags
4 backpacks
1 hard sided camera gear pack about the size of a small cooler
1 case of water
2 purses
140 gallons of avgas
And we didn't put anything in the wing lockers besides the stuff that lives there (covers, oil etc)
Didn’t the OP already start another post saying he gave up on the twin and is looking for a 6 seat Piper?
The baggage area is pretty small though, because the gear takes up a lot of it, right?
That's pretty impressive. I have a Yeti 65 and it's too big for any reasonable loading scenario in my Arrow. I borrowed a 45 for Oshkosh and have since bought an RTIC 30 soft-sided cooler for those times I need a cooler in the plane.It's hard to see in the photo but this is what we hauled in the 310R this weekend to Reno. 4 peoples worth of stuff and we hauled some extra for friends taking the airlines. Included but not limited to...
2 hard sided Yeti 65 coolers
1 soft sided Yeti 18 cooler
1 approximately 1 gallon Yeti bottle
1 approximately 1/2 gallon Yeti bottle
2 Hydroflasks
4 duffle bags
4 backpacks
1 hard sided camera gear pack about the size of a small cooler
1 case of water
2 purses
140 gallons of avgas
Looks great, 1300 lbs. of payload with full fuel! I wonder if the Lom Praha M337C-A V engines are FAA certified?The AeroVolga LA8 could fit your bill: http://www.aerovolga.com/uploads/files/LA-8_new_booklet.pdf
View attachment 77812
Best recommendation would be to sit down with your AP/IA and go over your entire mx plan. I provided owner-assisted mx for a number of years and this worked for most people. Once your collective plan is decided then you can decide what you can do on your own and those items you'd like to do under your mechanic's supervision. Each situation is unique so build your plan on your aircraft and AP/IA input. As to what you can legally perform through preventative maintenance can be found in Part 43 Appendix A(c) plus an FAA AC 43-12A.I'm also looking for a maintenance guide of some sort. Like, recommended service intervals for items owners can accomplish.
Best recommendation would be to sit down with your AP/IA and go over your entire mx plan.
As to what you can legally perform through preventative maintenance can be found in Part 43 Appendix A(c) plus an FAA AC 43-12A.