midcap
Pattern Altitude
Can you answer the question?
yes, if you check you mils when applying the paint you can do the calculation prior. simple math dude
Comanche Needs a New Paint Job
- Thread starter Dean Chesnut
- Start date
yes, if you check you mils when applying the paint you can do the calculation prior. simple math dude
True. But I already know how to calculate paint weight. The only question I asked was as follows: "Is there something that makes Axel advantageous over the current aviation products I'm not seeing?" Do you have an answer for it?
MooneyDriver78
En-Route
- Joined
- Aug 13, 2013
- Messages
- 4,692
- Display Name
Display name:
Tom
I didn’t paint stripes on my control surfaces, single color only to keep them as light as possible.
Chip Sylverne
Final Approach
- Joined
- Jun 17, 2006
- Messages
- 6,008
- Display Name
Display name:
Quit with the negative waves, man.
Not arguing the fact that out of balance control surface are not good, in fairness that video has nothing to do with paint.
- Joined
- Jun 7, 2008
- Messages
- 23,965
- Display Name
Display name:
Bob Noel
Maybe on some airplanes, but not the one I had. There was a reason I removed the wheel pants and rear seats.
midcap
Pattern Altitude
but in your case, all of that weight was very far from the moment of enertia, where as when you paint a plane the weight is spread out over the whole plane. Depending on thw eight distribution, you could come out pretty much in OG W&B specs.
- Joined
- Jun 13, 2008
- Messages
- 7,837
- Location
- Marietta, GA
- Display Name
Display name:
Drake the Outlaw
Probably 2/3 of the total surface area of the airplane is behind the CG, with a big chunk of that hung way out back. Repeat after me.... "Paint always moves the CG aft."
- Joined
- Jun 7, 2008
- Messages
- 23,965
- Display Name
Display name:
Bob Noel
You weren't talking about CG, you talked about "useful load"... and 30 pounds of useful load reduction is quite significant in the airplane I had, regardless of impact on CG.
- Joined
- Jun 7, 2008
- Messages
- 23,965
- Display Name
Display name:
Bob Noel
Paint always moves the CG aft
Mtns2Skies
Final Approach
- Joined
- Jul 12, 2008
- Messages
- 5,631
- Display Name
Display name:
Mtns2Skies
Paint always moves the CG aft.
MooneyDriver78
En-Route
- Joined
- Aug 13, 2013
- Messages
- 4,692
- Display Name
Display name:
Tom
Why?
midcap
Pattern Altitude
I am not talking about your plane....we are talking about the ops plane
midcap
Pattern Altitude
center on enertia is not directly in the middle of the total surface of the plane.
- Joined
- Jun 13, 2008
- Messages
- 7,837
- Location
- Marietta, GA
- Display Name
Display name:
Drake the Outlaw
Think about where the empty CG is on your airplane. Draw a spanwise line through that point. Estimate how much of the surface area of the airplane is behind that line. Probably 60% or more. Then think about how far aft a big chunk of that surface area is because of the area of the empennage.
So if you get a relatively even coat of paint on the airplane, it's gonna move the CG aft, because that's where the area and moments involved drive it. On something like a Mooney, I'd bet the absolute floor on a new paintjob is 20 pounds or so, 30 if you prime, and that's the floor. Up to 50 pounds probably isn't exceptional.
- Joined
- Jun 7, 2008
- Messages
- 23,965
- Display Name
Display name:
Bob Noel
bye-bye
30 Lbs is about average for the Two Seat Vans aircraft. Probably closer to 40 or 50 on a 4 seater certified aircraft with a light application. 4 to 6 gallons at 11lbs a gallon. Strip is the way to go and it’s not cheap. To do it properly the control surfaces need to come off at a minimum. After paint control surfaces need to be balanced and aircraft reweighed. If you are buying a aircraft that has been painted make sure this has been reflected in the logbook. If you sand and paint you will shift the CG aft as pointed out in other posts.
Last edited:
midcap
Pattern Altitude
Later Potater, haters gonna hate
midcap
Pattern Altitude
Op has a Comanche, the best ******** piston 4 seater ever made, you think 15 lbs of paint is gonna matteR?
- Joined
- Jun 13, 2008
- Messages
- 7,837
- Location
- Marietta, GA
- Display Name
Display name:
Drake the Outlaw
The entire thread has told you it won't be 15 pounds and that it will matter. What part don't you understand?
capg2000
Pre-takeoff checklist
My Skylane is in for paint right now... This is the 3rd plane I got painted.. Strip, corrosion removal acid etch and alodine went fine. Then the flap issue showed... Both flap skins(top) needed replaced. Lots of hail dings. R. bladder started leaking a few Mos. ago, so,
Waiting for the new R. Fuel bladder to show up & then it will be done... It's worth the wait.
Ace Aircraft Painting, Bartow, FL.
Great communicatior details on the prep job... So far I'm good.
1 thing I learned a long time ago is, Never paint over paint.... Strip. Clean, prep and prime /paint.
Waiting for the new R. Fuel bladder to show up & then it will be done... It's worth the wait.
Ace Aircraft Painting, Bartow, FL.
Great communicatior details on the prep job... So far I'm good.
1 thing I learned a long time ago is, Never paint over paint.... Strip. Clean, prep and prime /paint.
Yesterday we checked the balance of a C-150 rudder after a Tailbeacon installation. I was shocked to find it was slightly out of limits.On this unit the paint had been stripped! Easy fix but I’m sure the limits are there for a reason.
Snowmass
Line Up and Wait
I am still surprised that more people don't paint their own plane by themselves or with an A&P. The cost saving is huge and a dollar saved is about $2 earned when you consider ALL the taxes: Federal, State and FICA. I painted my C-210 for about 3 weeks work and I did not have to take my plane anywhere or stand in line. I was able to use my plane for about 2 of those 3 weeks in need be. The last week was the actual painting the other two stripping, etc.
- Joined
- Jun 13, 2008
- Messages
- 7,837
- Location
- Marietta, GA
- Display Name
Display name:
Drake the Outlaw
I can't think of a public airport around here that would knowingly allow you to paint an airplane in your hangar or on the ramp. Where'd you do this?
Huckster79
Pattern Altitude
- Joined
- Nov 22, 2018
- Messages
- 2,395
- Display Name
Display name:
Huckster79
Polished aluminum anyone?
Snowmass
Line Up and Wait
In my case in my own hangar on my own airstrip; however, I imagine most paint shops are on public airports. I painted a Mooney and Aeronca at the very public Bisbee-Douglas. Not all public airports (like people) are created equal. How could a fabric airplane be covered without spraying lacquer (dope)? Modern paints dry very fast and wet overspray doesn't travel very far. Another option would be to fly to a nearby private strip. I would gladly rent mine.
Chip Sylverne
Final Approach
- Joined
- Jun 17, 2006
- Messages
- 6,008
- Display Name
Display name:
Quit with the negative waves, man.
Exactly what friend of mine did on the Eastern Shore of MD with his project PA28. Rented a hangar on a little private grass strip. No electric so he brought a genny and shot the paint on with an airless sprayer. A little orange peel, but rubbed out pretty good.
Saved a ton.
30# is a lot to me, especially on a small plane like a 172.
jd21476
Line Up and Wait
Is this the Comanche for sale on Craigslist?
Snowmass
Line Up and Wait
As to control surface balance I removed the elevator and rudder and painted separately and had the balance checked by the A&P that reinstalled these. Weight on a C-210D is rarely a problem but it might be on more weight challenged aircraft. Also, I rarely get even close to gross as I have largely stopped carrying PAX due to liability risks. A $100K/seat limit is a cruel joke.